INTECHFLOOR

Guides

Installing the Mat 2.0 counting mat, step by step

Mat 2.0 needs no technician: lay one mat per 50 cm section of passage, cover them with a cover mat overlapping by at least 15 cm, plug the gateway into the mains no more than 8 m away, then set up the passage in the app. Set-up takes about 10 minutes.

Updated 1 October 2026

What do you need?

  • The counting mats (M2M10): 1 m × 0.59 m × 12 mm, 2.8 kg each. Each mat covers 50 cm of passage width.
  • The gateway (M2G10): built-in 4G, Wi-Fi and Ethernet, 220-240 VAC power (or 110-127 VAC). It takes 1 to 10 mats, so a passage from 50 cm to 5 m.
  • The connector (3 m) and, if needed, an extension (5 m).
  • A suitable cover mat, indoor or outdoor. It is mandatory.
  • The Technis Counting app on iOS, Android or the web, with an active Counting Service.

Step 1: how many mats do you need?

Measure the width of the passage from one side to the other and divide by 50 cm. A 1.5 m door needs 3 mats, a 5 m entrance needs 10. The passage must be fully covered: nobody should be able to walk around the mats. For an entrance wider than 5 m, plan a second gateway.

Passage widthNumber of matsMat 2.0 pack
50 cm1€580 excl. VAT
1 m2€830 excl. VAT
2.5 m5€1,580 excl. VAT
5 m10€2,830 excl. VAT

Step 2: where should the gateway go?

The gateway is designed for indoor use: install it under cover, near a mains socket. It must be no more than 8 m from the mats (3 m connector plus 5 m extension). It runs on mains power only; its battery is just for a clean shutdown. Check 4G coverage at the chosen spot; if it is poor, use Wi-Fi or Ethernet. If the network drops, a buffer keeps the counts.

Step 3: lay the mats

Lay the mats side by side on a clean, flat floor across the full width of the passage. The mats are rated IP54, take a load of 500 kg and operate from 0 to 50 °C. Connect them to the gateway with the connector.

Step 4: lay the cover mat

The cover mat is mandatory: it protects the sensors and ensures accuracy. Follow four rules:

  • overlap of at least 15 cm around the counting mats (20 cm outdoors);
  • no thicker than 15 mm;
  • no heavier than 3.5 kg/m²;
  • even texture, with no ridges or thicker areas.

Step 5: outdoors, add the platform

Outdoors, use the outdoor cover mat and first lay the outdoor platform of rigid, draining tiles, suitable for any ground (grass, gravel, paving, slabs, asphalt…), to provide a flat, stable surface. Without these, an outdoor installation is not covered by the warranty. The gateway must stay sheltered from the weather. This is the set-up that allowed 65 mats to be used outdoors for 2 months at the Paris 2024 Olympic flame site (see the Paris 2024 Olympic flame case study).

Step 6: plug in and configure

Plug the gateway into the mains: it connects over 4G on its own. In the Technis Counting app, add the gateway, name the passage and set your occupancy alert thresholds. No calibration is needed. Full set-up is stated at 10 minutes.

Step 7: check the count

Walk through a few times in both directions and check that entries and exits appear correctly in the app. Stated accuracy is up to 98% in optimal conditions, meaning a fully covered passage and a compliant cover mat. For trade shows and festivals, see also trade show footfall.

Where can you order the equipment?

The passage pack, cover mats and outdoor platform are available in the shop, and full technical details are on the Mat 2.0 people counting mat page. If you would rather test the system before buying, request a pilot.

Frequently asked questions

Do you need a technician to install a counting mat?

No. Mat 2.0 is plug and play: no drilling, no network cabling, no calibration. The gateway connects over 4G on its own. Technis technical support is available Monday to Friday, 9 am to 6 pm CET, if you have questions.

Can the Mat 2.0 gateway run on battery?

No. The gateway runs on mains power only (220-240 VAC or 110-127 VAC, 30 W max). Its internal battery is only there for a clean shutdown in a power cut. If the network drops, a buffer keeps the counts until the connection returns.

How far from the mats can the gateway be placed?

Up to 8 m. The connector is 3 m long and a 5 m extension can be added. Beyond that, the gateway must be moved closer to the passage.

Which cover mat should be used on Mat 2.0?

A cover mat is mandatory. It must overlap the counting mats by at least 15 cm on every side (20 cm outdoors), be no thicker than 15 mm, weigh no more than 3.5 kg/m² and have an even texture. Intechfloor offers indoor and outdoor cover mats, standard or custom.

Try Mat 2.0 at your next event.

A guided pilot: installation, live data and a full report. Then you choose: buy or subscribe.

Request a pilot Shop